Vehicles
Sections
307 not categorized PORSCHE 996 WE NEED A CARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 (includes uncategorized and accessory items) 115900944018CS Sports suspension for 924 - 944 - 968 only for 18mm spring strut mounting this sports suspension is for everyday use and increase the dynamic and response. The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$3,132.80
Make a selection 115900997BIGT3D Bilstein b16 damptronic not only engine performance but, above all, suspension technology contributes to the fascination of a Porsche sports car. Bilstein offers an range of active coil over systems of the current Porsche models with pasm. The coil over system is electronically adjustable. So pasm-function and car sensors like psm stays fully in function. In addition the height-adjustment offers a certified range of lowering. Discreet sporty looks and precisely defined response within both setup modes, accompanied by high driving dynamics and excellent residual ride comfort. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it...(choose a part on the right to read more)
$5,330.60
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 115910996032 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,682.59
Make a selection 115900997TTCS The ultimate bilstein sport suspension for club racing and street performance! This suspension was developed under real racing conditions by bilstein with double world rally champion walter rohrl. - reduced weight via the use of an integrated reservoir. - 2 way damping adjustment (bound (red) and rebound (blue) independently). - dials with good visibility and scaling (from 1 to 10). - easy to adjust when installed with click screening and color coding. - bilstein mono-tube gas pressure technology. - adjustable aluminum uniball camber plates (rear). - TUV approved. - made in Germany. What's in the box: - adjustable dampers including double springs. - rear uniball camber plates. - spring tensioning key (tool). -...(choose a part on the right to read more)
$7,256.70
Make a selection 115910996033 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,784.11
Make a selection 115910996034 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,784.11
Make a selection 115910997003 Bilstein b4 OEM i030 with pasm (original i030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory i030 sport suspension. Nothing is better than the original! The b4 i030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model i030 with pasm
$2,983.16
Make a selection 150BA79185 Increase the horsepower of your 914/6 or 916 with bursch performance headers. They have been dyno, track and street tested since 1958. Bursch headers are available in a variety of diameters to suit your displacement and driving preference. Each hand made header is mandrel bent from durable 16-gauge steel and is coated with 1,200-degree high temp paint. Features: increased horsepower and torque weight savings 16 gauge steel coated in 1,200 degree high temperature paint sold as a set (left and right). 1 necessary per car. Please note: this replaces your stock heat exchangers and does not include heat. These headers do not include provisions for o2 or temperature sensors. Use of this product for purposes other tha...(choose a part on the right to read more)
$1,335.40
Make a selection 150BP264 Book description: publication date: january 15, 1999 inside this manual you will find routine maintenance, tune-up procedures, engine repair, cooling and heating, air conditioning, fuel and exhaust, emissions control, ignition, brakes, suspension and steering, electrical systems, and wiring diagrams.
$108.90
Make a selection 150TB1126 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$328.90
Make a selection 150TB1821 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle. General Fitment912 1965-69911 1970-73
From $312.70
Make a selection 150TB182301 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: lighter weight hollow torsion bar set manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle. General Fitment912 1965-69911 1970-73
From $356.11
Make a selection 17092102S This cross over connector replaces original part # 930 111 157 01, it is a quality stainless steel replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 93011119307 and sealing ring, part # 91111118903 sold individually. 1 necessary per car.
$82.50
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,311.00
Make a selection 21011196538 This sport muffler is engineered for the discerning Porsche 965 turbo owner who is interested in pure unbridled power and sound. It is hand made from t 321 grade stainless steel. All piping is mandrel bent for reduced backpressure and increased performance. The sport muffler exudes a lower, deeper linear-firing-order dominated flat 6 Porsche turbo sound with added turbo whistle. Exhaust tips are 76 mm (3 inch) polished ovals with a rolled lip. Each kit includes complete installation hardware, wastegate pipe and clamps. Features: gains of up to 10 hp more* t 321 stainless steel mandrel bent new wastegate pipe new gaskets new hardware new muffler clamps *dependent upon boost level and other modifications. Sold in...(choose a part on the right to read more)
$2,127.42
Make a selection 220110901ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.8-inch (71 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is remanuf...(choose a part on the right to read more)
$485.10
Make a selection 22011098100 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,529.00
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,094.50
Make a selection 24001670 Bilsteins are original equipment on many Porsches and have won, for Porsche, countless races. Bilsteins are the highest quality shocks made and will last the lifetime of your Porsche. Bilstein heavy-duty shocks and struts provide improved handling and stability without sacrificing the ride. Their superior damping ability makes them ideal for spirited driving while still maintaining an exceptional "street" feel. As with all bilsteins, these units instantaneously self-adjust to changing road surfaces. In addition, their performance does not gradually decline from age, use or heat - requiring no compensating manual adjustments as with conventional multi-tube units. Sold each, two needed for the rear of your vehi...(choose a part on the right to read more) General Fitment911 1970-73911 1965-69 912 1965-69
$223.56
Make a selection 240600101 Waterproof cloth tape for reliable sealing, masking or concealing of racing fender benders. High initial tack and extremely good adhesion. Pe coated cloth tape, waterproofed. Excellent for repairs, crafting and fixing. Extra strong adhesion, which also allows installation on uneven surfaces. 50 mm wide x 50 meters long.
$18.70
Make a selection 240600103 Waterproof cloth tape for reliable sealing, masking or concealing of racing fender benders. High initial tack and extremely good adhesion. Pe coated cloth tape, waterproofed. Excellent for repairs, crafting and fixing. Extra strong adhesion, which also allows installation on uneven surfaces. 50 mm wide x 50 meters long.
$18.70
Make a selection 240600106 Waterproof cloth tape for reliable sealing, masking or concealing of racing fender benders. High initial tack and extremely good adhesion. Pe coated cloth tape, waterproofed. Excellent for repairs, crafting and fixing. Extra strong adhesion, which also allows installation on uneven surfaces. 50 mm wide x 50 meters long.
$18.70
Make a selection 240911352BH Pagid blue rs42 are from the rs line of all around racing brake pads. They are a medium friction coefficient racing compound with medium initial bite and good cold friction. Rs42 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and are very stable over that wide temperature range. Rs42 pads offer excellent pedal feel and inspire confidence in extreme braking situations. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: vintage rally racing, formula racing and touring cars. Features at a glance: medium friction coefficient medium initial bite goo...(choose a part on the right to read more) General Fitment912 1965-69911 1970-73 356 1960-65
From $192.92
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |